|
About the Print Quality Issues category
|
|
0
|
3
|
March 8, 2026
|
|
Poor print quality on Bambu with original filament: drying, calibration, and AMS on top
|
|
14
|
23
|
March 20, 2026
|
|
Discussion of printing with 0.6–0.8 line width and better layer fusion
|
|
5
|
11
|
March 17, 2026
|
|
ABS-GF: how to check that the layers fuse properly
|
|
4
|
20
|
March 16, 2026
|
|
OrcaSlicer has a setting to eliminate gaps between perimeters and the top layer
|
|
2
|
16
|
March 16, 2026
|
|
ABS enclosure: a detached “tail,” adhesion, and whether the plate warped
|
|
7
|
11
|
March 12, 2026
|
|
PETG ironing: speed, gaps, and why the material is hard to iron
|
|
3
|
40
|
March 8, 2026
|
|
Top-surface ironing: should it be enabled and what settings to use
|
|
14
|
20
|
March 7, 2026
|
|
Printing gears from pure nylon: speed, chamber, and a 0.2 nozzle
|
|
2
|
9
|
March 3, 2026
|
|
OrcaSlicer prints the first perimeter in midair because of the printer profile
|
|
4
|
9
|
February 9, 2026
|
|
Printing with pure PP: adhesion to FR4, shrinkage, and staying flexible
|
|
3
|
8
|
January 20, 2026
|
|
Improving and offsetting the airflow guide
|
|
3
|
7
|
January 15, 2026
|
|
Which PP GF/CF materials print well through a 0.4 nozzle
|
|
6
|
9
|
December 14, 2025
|
|
Can wet filament be stored in a vacuum bag instead of drying it
|
|
5
|
11
|
November 22, 2025
|
|
Warping of a large ABS GF10 part and attempts to relieve internal stress
|
|
4
|
9
|
October 29, 2025
|
|
Extrusion gaps at the start of bridges: possible PA and slicing settings
|
|
8
|
13
|
October 21, 2025
|
|
Printing Ultem/nylon on FR4/PEI: glue, bed temps, and drying
|
|
13
|
22
|
October 21, 2025
|
|
How to disable circular marks on the print surface
|
|
1
|
3
|
October 16, 2025
|
|
How to tune first layer and flow on rough plastic
|
|
10
|
9
|
October 13, 2025
|
|
Internal bridges in Orca are not extruding: looking for the cause
|
|
6
|
11
|
October 6, 2025
|
|
Drying filament: TPU is more critical than PLA, almost everything gets dried
|
|
3
|
8
|
October 5, 2025
|
|
ASA: corners lifting on a case during printing
|
|
2
|
10
|
October 5, 2025
|
|
Very soft 75A TPU from FDPlast: how to print it on Q1
|
|
3
|
8
|
October 4, 2025
|
|
Nozzle offset relative to the sensor and how to use the probing grid
|
|
7
|
8
|
October 2, 2025
|
|
Printing PLA/PETG/TPU in an enclosed chamber on the Neptune 3 Pro: out of the box or after mods
|
|
4
|
6
|
October 1, 2025
|
|
How to remove glue marks and whitening from a part after taking it off the bed
|
|
5
|
6
|
September 28, 2025
|
|
How to remove white marks and tears on ABS after taking it off the bed
|
|
5
|
17
|
September 28, 2025
|
|
Problem with STL dimensions after export and fix status
|
|
5
|
7
|
September 25, 2025
|
|
How drying temperatures were chosen and whether plastic really becomes brittle after drying
|
|
10
|
13
|
September 16, 2025
|
|
The case cracks on first heating: how the case was printed and why the author didn't print it themselves
|
|
7
|
8
|
September 13, 2025
|