|
Composite plastic as a way to reduce shrinkage and hotend limitations
|
|
5
|
0
|
August 27, 2025
|
|
Assembly issues with iDryer Unit Duo: enclosure shrinkage and tight fits
|
|
14
|
0
|
August 27, 2025
|
|
Printing PA12 with a 0.2 mm nozzle: holes and underextrusion
|
|
4
|
0
|
August 25, 2025
|
|
Printed tubes and shafts: where the line is between printed and metal
|
|
5
|
0
|
August 16, 2025
|
|
Corners warping on PP: effect of layer time, temperature, and cooling
|
|
5
|
0
|
July 28, 2025
|
|
Printing the enclosure: layer too fine at 0.1 and defects on overhangs
|
|
1
|
0
|
July 26, 2025
|
|
What grit sandpaper to use on FR4 for better PP adhesion
|
|
11
|
0
|
July 25, 2025
|
|
PP GF30 or PA6 GF30 for the part by the cylinder: heat resistance and initial print settings
|
|
12
|
0
|
July 24, 2025
|
|
A large ABS part peels off the bed: clips, glass, and lowering speed
|
|
10
|
0
|
July 17, 2025
|
|
Printing with composites: is a 0.4 nozzle enough or is 0.6 better
|
|
5
|
0
|
July 13, 2025
|
|
Which surface is best for printing PA GF30
|
|
2
|
0
|
July 10, 2025
|
|
How to make the Light diffuser cover: materials, light transmission, and a two-color print option
|
|
6
|
0
|
July 3, 2025
|
|
What to print large ABS parts with if the walls warp into an arc
|
|
6
|
0
|
June 25, 2025
|
|
Do you need to dry nylon before every print if it’s stored in a vacuum bag
|
|
5
|
0
|
June 12, 2025
|
|
Holes in seams in Orca when printing ABS: how to calibrate PA and what else to check
|
|
6
|
0
|
May 31, 2025
|
|
ABS stand 250×100 mm warps into an arc after cooling: causes and what helped
|
|
5
|
0
|
May 30, 2025
|
|
ABS prints look semi-transparent because the walls are too thin
|
|
4
|
0
|
May 15, 2025
|
|
Don't like the flow splitters: they break, maybe unfinished
|
|
1
|
0
|
April 28, 2025
|
|
First impressions of NextSPD adhesive: holds prints, but smells strong
|
|
6
|
0
|
April 23, 2025
|
|
Photopolymer in syringes: too thick, leaked inside, second attempt worked better
|
|
4
|
0
|
April 21, 2025
|
|
Printed part seems wrong despite other parts fitting
|
|
4
|
0
|
April 21, 2025
|
|
Printing Ultem: sticking to PEI/PVP and bed temperature
|
|
3
|
0
|
April 21, 2025
|
|
What adhesive sandwich holds clean PC and how to remove the part afterward
|
|
4
|
0
|
April 6, 2025
|
|
After painting, the model gets red bleed-through on the second layer: looking for a setting in Orca
|
|
6
|
0
|
April 4, 2025
|
|
Polycarbonate printing tests: adhesives, bed, and PVP mix
|
|
3
|
0
|
April 3, 2025
|
|
Ultran sticks to FR4, but a glued backing plate is needed
|
|
2
|
0
|
March 30, 2025
|
|
How to make FDM prints waterproof for a cup/part that holds water
|
|
14
|
0
|
March 25, 2025
|
|
Case shrinkage, old print settings, and plans to reprint for high temperature
|
|
4
|
0
|
March 13, 2025
|
|
Thin wall in the model: a “hole” and strange slicing in the slicer
|
|
7
|
0
|
March 8, 2025
|
|
How to orient a part for printing: against the bed, chamfers, and whether supports are needed
|
|
5
|
0
|
March 1, 2025
|