|
Filament ran out near the end of the print: pause or M600
|
|
6
|
0
|
February 27, 2025
|
|
Beating Terylene: working print settings
|
|
4
|
0
|
February 27, 2025
|
|
Printing the Unit: will one spool be enough, and which ABS to choose for the enclosure
|
|
4
|
1
|
February 22, 2025
|
|
PPGF30 on a 0.4 nozzle: clogs vs uneven flow, and why 0.5 seems better
|
|
6
|
0
|
February 22, 2025
|
|
Speed test, actual print speeds, and material/nozzle limits
|
|
15
|
0
|
February 21, 2025
|
|
Who successfully prints POM: how to get adhesion
|
|
3
|
0
|
February 20, 2025
|
|
Baking PLA in a matrix and the idea of getting a more monolithic part
|
|
4
|
0
|
February 20, 2025
|
|
Problems with a 0.6 nozzle: seam gap, holes, and whether to go back to 0.4
|
|
21
|
0
|
February 19, 2025
|
|
ABS: temperature, tower, and weak layer adhesion
|
|
2
|
0
|
February 19, 2025
|
|
Bubbles, seam, and ABS print settings on Qidi Q1
|
|
6
|
0
|
February 19, 2025
|
|
Stripes on a nylon super carbon part: a visual defect across the whole surface
|
|
5
|
1
|
February 15, 2025
|
|
Printing lid problems caused by solid infill in Orca
|
|
4
|
1
|
February 13, 2025
|
|
Thermal post-processing report after printing and drying the spool in iDryerX
|
|
4
|
1
|
February 7, 2025
|
|
How to dry Ultran M20 and how much plastic is needed to print the Unit
|
|
4
|
0
|
February 6, 2025
|
|
How to reduce the risk of a failed 14-hour print
|
|
2
|
0
|
February 5, 2025
|
|
Setting line width for a 0.4 nozzle
|
|
5
|
0
|
February 5, 2025
|
|
Retraction issues on Terylene CFF: part photo and retraction tests
|
|
1
|
1
|
February 4, 2025
|
|
Experience with PVB/BF2 coating for adhesion and a mixture recipe
|
|
1
|
1
|
February 3, 2025
|
|
Juice on glass for nylon: why it peels off and how to bake it
|
|
6
|
0
|
February 3, 2025
|
|
Printing units without supports: do you need support for the base
|
|
4
|
0
|
February 3, 2025
|
|
How to properly cure BF-2 so the coating lasts longer
|
|
4
|
0
|
November 30, 2024
|
|
After changing the nozzle, PLA delaminates; advice is to check offset and temperature
|
|
6
|
1
|
November 26, 2024
|
|
ABS CF without chamber: enclosure and nozzle temperature discussion
|
|
5
|
0
|
November 6, 2024
|
|
PF6-GF stringing: retraction too high on direct drive, suggested test and lower values
|
|
5
|
0
|
November 5, 2024
|
|
Does salty sea air affect plastic drying and printing
|
|
12
|
0
|
October 29, 2024
|
|
Discussion of defects on the model: pressure advance or retraction?
|
|
4
|
0
|
October 17, 2024
|
|
Single-wall box: edge peeling and how critical it was
|
|
2
|
0
|
October 7, 2024
|
|
PETG warps parts and grilles after removal from the bed
|
|
6
|
0
|
October 7, 2024
|
|
Do you need a thermal chamber for PPGF, and how does it affect part properties?
|
|
3
|
0
|
October 7, 2024
|
|
A strange pattern on the part caused by the feeder/BMG
|
|
7
|
0
|
October 5, 2024
|