|
🔴 iDryer Support & Setup (Question Template)
|
|
0
|
48
|
March 7, 2026
|
|
What is iDryer Link and where to find the documentation
|
|
1
|
80
|
March 30, 2026
|
|
Overheat protection for the heater: second sensor, KSD, and firmware limits
|
|
9
|
40
|
March 30, 2026
|
|
Discussion of dual-loop PID and temperature control in the dryer
|
|
5
|
27
|
March 29, 2026
|
|
Should consumables and small assembly parts be included in the kit
|
|
8
|
26
|
March 29, 2026
|
|
How to wire an RC snubber for the heater/cooler and which parts to use
|
|
2
|
20
|
March 27, 2026
|
|
Enclosure notes: access to the bottom screws, outlet mounting, and cracks near the holes
|
|
5
|
17
|
March 25, 2026
|
|
Temperature sensor error: BME280, a reference thermistor, and the idea of switching to SHT31
|
|
3
|
15
|
March 23, 2026
|
|
Does the ESP in iDryer need separate power
|
|
14
|
30
|
March 17, 2026
|
|
How much plastic is used for the iDryer body and parts
|
|
4
|
32
|
March 10, 2026
|
|
The iDryer display wouldn’t start after soldering, but the issue was fixed
|
|
6
|
18
|
March 9, 2026
|
|
Joke about iDryer kitchen/bedroom and “boil the dryer”
|
|
2
|
14
|
March 8, 2026
|
|
An idea for a DIY blower/dryer with a hair-dryer impeller
|
|
2
|
17
|
March 7, 2026
|
|
Standalone iDryer needs extra control: screen or ESP32
|
|
10
|
44
|
March 6, 2026
|
|
Openness of iDryer X and Unit, documentation, and firmware publishing
|
|
2
|
23
|
March 4, 2026
|
|
Help with OLED screens: one is not detected as SSD1306
|
|
1
|
16
|
March 2, 2026
|
|
Which humidity sensors are supported in the Unit, and how to check SHT31 readings
|
|
12
|
21
|
March 1, 2026
|
|
When will the Unit be back in stock, and will kits be available only
|
|
4
|
24
|
March 1, 2026
|
|
Where to find the file for cutting the scale-module carriages
|
|
2
|
10
|
February 27, 2026
|
|
SHT31 in the dryer won’t drop humidity below 37–40% at 65°C
|
|
4
|
15
|
February 24, 2026
|
|
Can V4 be built from the MCU EXT Kit, and do you need a separate host for Klipper
|
|
5
|
23
|
February 24, 2026
|
|
Does the SHT sensor in iDryer need calibration, and how does SHT30 differ from SHT31
|
|
3
|
9
|
February 23, 2026
|
|
Are the iDryer X2 heating times to 90°C normal
|
|
2
|
9
|
February 23, 2026
|
|
Replacing the stock snail fan with a 220V fan for the dryer/heater
|
|
7
|
14
|
February 23, 2026
|
|
Realtime 25–90 run and an idea to track moisture and weight-loss champions
|
|
2
|
10
|
February 22, 2026
|
|
Replaced FOD814, heater issue fixed, board swap can come later
|
|
2
|
7
|
February 22, 2026
|
|
Load-cell stability, temperature effects, and range selection for iDryer
|
|
14
|
19
|
February 21, 2026
|
|
Where to get iDryer Unit/X boards and is there documentation
|
|
13
|
40
|
February 21, 2026
|
|
Is there a schematic or Gerbers for the iDryer Unit board
|
|
4
|
27
|
February 21, 2026
|
|
Questions about the iDryer Unit board, Klipper, and dryer design tweaks
|
|
6
|
25
|
February 21, 2026
|