|
Wrong AutoPID coefficients and delta setup after firmware 0.5.8
|
|
4
|
4
|
January 5, 2026
|
|
How best to install the thermal fuse and secure the thermistor
|
|
1
|
7
|
January 4, 2026
|
|
Question about running iHeater through the printer’s serial port
|
|
2
|
7
|
December 28, 2025
|
|
AutoPID for the heater: what parameters to set and why it’s better to disable Kd
|
|
8
|
13
|
December 20, 2025
|
|
Temperature overshoot on iHeater and the need for PID tuning
|
|
5
|
7
|
December 20, 2025
|
|
How to modify the standalone iHeater firmware to remove the slow-heating error
|
|
8
|
8
|
December 17, 2025
|
|
How air and heater temperatures are displayed, and when the timer starts
|
|
4
|
3
|
December 12, 2025
|
|
The heater housing melted a little after long chamber use
|
|
2
|
6
|
November 27, 2025
|
|
Heater temperature spikes after reaching the target temperature
|
|
6
|
7
|
November 23, 2025
|
|
How to print an iHeater part in two colors in OrcaSlicer
|
|
4
|
6
|
October 29, 2025
|
|
iHeater for P1S: is it compatible, standalone mode, and where to buy
|
|
9
|
10
|
October 21, 2025
|
|
Error classes and emergency heater shutdown via relay
|
|
17
|
5
|
October 3, 2025
|
|
Photo of a Neptune with iHeater and a homemade active filter
|
|
2
|
4
|
October 1, 2025
|
|
How safe is it to heat a Neptune in a heated chamber, and how to control electronics temperature
|
|
16
|
31
|
October 1, 2025
|
|
Discussion of the conflict around iHeater in FF and Nazym's experience
|
|
4
|
3
|
September 17, 2025
|
|
How to measure bed heating uniformity cheaply
|
|
6
|
6
|
September 16, 2025
|
|
Choosing a 220V fan and heater for a dual iHeater
|
|
5
|
7
|
September 15, 2025
|
|
Checking variable_delta_high: air temperature, warm-up, and risk of melting the ABS case
|
|
14
|
13
|
September 13, 2025
|
|
Finding the heater bracket model in iDryer V2
|
|
7
|
9
|
September 11, 2025
|
|
What wire gauge to use to extend the heater wires
|
|
2
|
9
|
September 10, 2025
|
|
A case of a burned 5V PSU and fuse after a long print
|
|
2
|
6
|
September 7, 2025
|
|
How to choose heater power for an active SV08 Max thermal chamber
|
|
5
|
9
|
September 7, 2025
|
|
Do the thermistor need to be moved into the heatsink, or is setting the heater delta enough?
|
|
6
|
6
|
September 3, 2025
|
|
Request to redesign the cover/flange for iHeater and submit a PR
|
|
3
|
4
|
September 3, 2025
|
|
Comparing iHeater heating on 0.5.5 and 0.5.8 firmware and checking with an external thermistor
|
|
16
|
17
|
September 2, 2025
|
|
Enclosure material for iHeater: PIR or acrylic
|
|
2
|
3
|
September 2, 2025
|
|
Installing a heater/backlight in Bambu: mounting, chamber heating, and cable routing
|
|
4
|
6
|
August 27, 2025
|
|
Connecting iHeater to 220V mains and standalone mode
|
|
3
|
5
|
August 26, 2025
|
|
Should a KSD thermal switch be installed in a silicone sleeve
|
|
4
|
5
|
August 25, 2025
|
|
Why the iHeater board needs an AC-DC converter
|
|
4
|
8
|
August 24, 2025
|