# Warping of a large ABS GF10 part and attempts to relieve internal stress

**URL:** <https://forum.idryer.org/t/warping-of-a-large-abs-gf10-part-and-attempts-to-relieve-internal-stress/1560>\
**Category:** Print Quality Issues\
**Created:** [October 29, 2025, 4:51pm UTC](https://forum.idryer.org/t/warping-of-a-large-abs-gf10-part-and-attempts-to-relieve-internal-stress/1560 "2025-10-29T16:51:56Z")\
**Posts on this page:** 5\
**Page:** 1

<div class="post-metadata">

**Author:** ![eg\_or\_h2\_sborki\_6462](https://forum.idryer.org/letter_avatar_proxy/v4/letter/e/ecc23a/32.png) [@eg\_or\_h2\_sborki\_6462](https://forum.idryer.org/u/eg_or_h2_sborki_6462)\
**Post date:** [October 29, 2025, 4:51pm UTC](https://forum.idryer.org/t/warping-of-a-large-abs-gf10-part-and-attempts-to-relieve-internal-stress/1560/1 "2025-10-29T16:51:56Z")

</div>

That big part warped this much

On the two small ones I tried different solid layer patterns to see if it makes a difference. I was betting on Hilbert, but it warped even more than the monotonic one.

P.S. don’t look at the chewed-up edges, the pliers were hungry

At the same time, the bed didn’t warp.  
It cooled down by itself in the printer for half the night

> **🇷🇺 Оригинал**
>
> Большую деталь так закрутило
> 
> На двух мелких ставил разных шаблон сплошных слоев, проверить влияет ли. Ставка была на гильберта,но его закрутило сильнее монотонного.
> 
> зы на погрызанные края не смотрите, плоскогубцы были голодные
> 
> при этом, стол не загнуло.  
> остывало пол ночи само в принтере

---

<div class="post-metadata">

**Author:** ![ruslan\_p\_261](https://forum.idryer.org/letter_avatar_proxy/v4/letter/r/f04885/32.png) [@ruslan\_p\_261](https://forum.idryer.org/u/ruslan_p_261)\
**Post date:** [October 29, 2025, 4:55pm UTC](https://forum.idryer.org/t/warping-of-a-large-abs-gf10-part-and-attempts-to-relieve-internal-stress/1560/2 "2025-10-29T16:55:19Z")

</div>

The usual practice is: print it, let it cool on the bed until the point where you can pull it off, then put it on the table and heat it again to 90-100, whatever you normally run the bed at, but for flat parts like in the first video it only helps partially

> **🇷🇺 Оригинал**
>
> Практика такая, печать, охлаждение на столе до состояния когда можно оторвать, потом положил на стол и греешь опять на 90-100 сколько обычно стол, но плоские детали как на первом видео спасает лишь отчасти

---

<div class="post-metadata">

**Author:** ![eg\_or\_h2\_sborki\_6462](https://forum.idryer.org/letter_avatar_proxy/v4/letter/e/ecc23a/32.png) [@eg\_or\_h2\_sborki\_6462](https://forum.idryer.org/u/eg_or_h2_sborki_6462)\
**Post date:** [October 29, 2025, 4:56pm UTC](https://forum.idryer.org/t/warping-of-a-large-abs-gf10-part-and-attempts-to-relieve-internal-stress/1560/3 "2025-10-29T16:56:59Z")

</div>

And why reheat it?

> **🇷🇺 Оригинал**
>
> а зачем повторный нагрев?

---

<div class="post-metadata">

**Author:** ![ruslan\_p\_261](https://forum.idryer.org/letter_avatar_proxy/v4/letter/r/f04885/32.png) [@ruslan\_p\_261](https://forum.idryer.org/u/ruslan_p_261)\
**Post date:** [October 29, 2025, 4:58pm UTC](https://forum.idryer.org/t/warping-of-a-large-abs-gf10-part-and-attempts-to-relieve-internal-stress/1560/4 "2025-10-29T16:58:42Z")

</div>

There are some internal stresses in it, meaning it was hot, then it cooled down, stresses appeared and pulled it out of shape, so you heat the part up a lot to relax them. It gets better, but it’s not a cure-all

> **🇷🇺 Оригинал**
>
> есть там какие-то внутренние напряжения, т.е. оно было грячим, потом остыло, напряжения появились и потянули, ты греешь сильно деталь чтобы их ослабить. Оно лучше, но не панацея

---

<div class="post-metadata">

**Author:** ![eg\_or\_h2\_sborki\_6462](https://forum.idryer.org/letter_avatar_proxy/v4/letter/e/ecc23a/32.png) [@eg\_or\_h2\_sborki\_6462](https://forum.idryer.org/u/eg_or_h2_sborki_6462)\
**Post date:** [October 29, 2025, 4:58pm UTC](https://forum.idryer.org/t/warping-of-a-large-abs-gf10-part-and-attempts-to-relieve-internal-stress/1560/5 "2025-10-29T16:58:57Z")

</div>

I was also thinking, what if after the print finishes, you bake the part on the bed at 130+C, then clamp it down with a plate (warm) and leave it to cool?

Yeah, makes sense.

Feels like the real cure would be a chamber temperature above 65C, like 80-90

> **🇷🇺 Оригинал**
>
> еще думал, что если после окончания печати прожарить деталь на столе 130+гр, потом прижать плитой(теплой) и оставить остывать ?
> 
> да, логично
> 
> как будто панацей бы было температура камеры выше 65гр, например 80-90