# Discussion of printing with 0.6–0.8 line width and better layer fusion

**URL:** <https://forum.idryer.org/t/discussion-of-printing-with-0-6-0-8-line-width-and-better-layer-fusion/1735>\
**Category:** Print Quality Issues\
**Created:** [March 17, 2026, 8:19am UTC](https://forum.idryer.org/t/discussion-of-printing-with-0-6-0-8-line-width-and-better-layer-fusion/1735 "2026-03-17T08:19:15Z")\
**Posts on this page:** 6\
**Page:** 1

<div class="post-metadata">

**Author:** ![tolyan\_ferz\_501](https://forum.idryer.org/letter_avatar_proxy/v4/letter/t/b9bd4f/32.png) [@tolyan\_ferz\_501](https://forum.idryer.org/u/tolyan_ferz_501)\
**Post date:** [March 17, 2026, 8:19am UTC](https://forum.idryer.org/t/discussion-of-printing-with-0-6-0-8-line-width-and-better-layer-fusion/1735/1 "2026-03-17T08:19:15Z")

</div>

I couldn’t get it to print at 0.8 width at all. When I set the outer wall width above 0.72 (I think), the cells of the middle wall would disappear. Ended up printing at 0.7.  
 ![](https://forum.idryer.org/uploads/default/original/2X/3/3009ba52c2b1d000b25609ebe605f337c0f914b4.jpeg)

> **🇷🇺 Оригинал**
>
> Ау меня вобще ен получилось шириной 08 печатать. При выставлении ширины наружней стенки больше 0,72 ( вроде бы ) пропадали ячейки средней стенки. Печатал 07 по итогу.  
> ![](https://forum.idryer.org/uploads/default/original/2X/3/3009ba52c2b1d000b25609ebe605f337c0f914b4.jpeg)

---

<div class="post-metadata">

**Author:** ![ruslan\_p\_261](https://forum.idryer.org/letter_avatar_proxy/v4/letter/r/f04885/32.png) [@ruslan\_p\_261](https://forum.idryer.org/u/ruslan_p_261)\
**Post date:** [March 17, 2026, 8:43am UTC](https://forum.idryer.org/t/discussion-of-printing-with-0-6-0-8-line-width-and-better-layer-fusion/1735/2 "2026-03-17T08:43:07Z")

</div>

Where does it say you need 0.8? I printed 0.6 just fine too)

> **🇷🇺 Оригинал**
>
> Это где написано про необходимость 0.8? Я и 0.6 печатал замечательно)

---

<div class="post-metadata">

**Author:** ![tolyan\_ferz\_501](https://forum.idryer.org/letter_avatar_proxy/v4/letter/t/b9bd4f/32.png) [@tolyan\_ferz\_501](https://forum.idryer.org/u/tolyan_ferz_501)\
**Post date:** [March 17, 2026, 8:44am UTC](https://forum.idryer.org/t/discussion-of-printing-with-0-6-0-8-line-width-and-better-layer-fusion/1735/3 "2026-03-17T08:44:49Z")

</div>

IMO the fusion is better.

> **🇷🇺 Оригинал**
>
> имхо спекаемость лучше.

---

<div class="post-metadata">

**Author:** ![ruslan\_p\_261](https://forum.idryer.org/letter_avatar_proxy/v4/letter/r/f04885/32.png) [@ruslan\_p\_261](https://forum.idryer.org/u/ruslan_p_261)\
**Post date:** [March 17, 2026, 8:46am UTC](https://forum.idryer.org/t/discussion-of-printing-with-0-6-0-8-line-width-and-better-layer-fusion/1735/4 "2026-03-17T08:46:28Z")

</div>

Fusion is better if you go slower and hotter). Starting from 0.6, the corners also stop being round and become square

> **🇷🇺 Оригинал**
>
> Спекаемост лучше медленнее и теплее). От 0.6 и углы уже не круглые а квадратные

---

<div class="post-metadata">

**Author:** ![tolyan\_ferz\_501](https://forum.idryer.org/letter_avatar_proxy/v4/letter/t/b9bd4f/32.png) [@tolyan\_ferz\_501](https://forum.idryer.org/u/tolyan_ferz_501)\
**Post date:** [March 17, 2026, 8:47am UTC](https://forum.idryer.org/t/discussion-of-printing-with-0-6-0-8-line-width-and-better-layer-fusion/1735/5 "2026-03-17T08:47:42Z")

</div>

Exactly. Slower, hotter, and press the top layer into the lower one a bit more

> **🇷🇺 Оригинал**
>
> Правильно. Медленнее, теплее и вдавливать верхний слдой в нижний посильнее

---

<div class="post-metadata">

**Author:** ![ruslan\_p\_261](https://forum.idryer.org/letter_avatar_proxy/v4/letter/r/f04885/32.png) [@ruslan\_p\_261](https://forum.idryer.org/u/ruslan_p_261)\
**Post date:** [March 17, 2026, 8:48am UTC](https://forum.idryer.org/t/discussion-of-printing-with-0-6-0-8-line-width-and-better-layer-fusion/1735/6 "2026-03-17T08:48:53Z")

</div>

![](https://forum.idryer.org/uploads/default/original/2X/d/d1b61857b9b716bf042148f9c5012b705efe271c.jpeg)

> **🇷🇺 Оригинал**
>
> ![](https://forum.idryer.org/uploads/default/original/2X/d/d1b61857b9b716bf042148f9c5012b705efe271c.jpeg)