# Are the iDryer X2 heating times to 90°C normal

**URL:** <https://forum.idryer.org/t/are-the-idryer-x2-heating-times-to-90-c-normal/1690>\
**Category:** iDryer\
**Created:** [February 23, 2026, 8:32pm UTC](https://forum.idryer.org/t/are-the-idryer-x2-heating-times-to-90-c-normal/1690 "2026-02-23T20:32:56Z")\
**Posts on this page:** 3\
**Page:** 1

<div class="post-metadata">

**Author:** ![evgenii\_komissa\_8bc4](https://forum.idryer.org/letter_avatar_proxy/v4/letter/e/aeb1de/32.png) [@evgenii\_komissa\_8bc4](https://forum.idryer.org/u/evgenii_komissa_8bc4)\
**Post date:** [February 23, 2026, 8:32pm UTC](https://forum.idryer.org/t/are-the-idryer-x2-heating-times-to-90-c-normal/1690/1 "2026-02-23T20:32:56Z")

</div>

Could someone tell me, those who have already built the dryer, are these normal heating timings for the X2 version? I set it to heat up to 90 degrees, delta 20  
Timeline:  
50 degrees - 2 minutes  
60 degrees - 4 minutes  
70 degrees - 6 minutes, heater 96 degrees  
80 degrees - 9 minutes, heater 106 degrees  
87 degrees - 13 minutes, heater 106 degrees  
89 degrees - 19 minutes, heater 102 degrees  
90 degrees - 24 minutes, heater 101 degrees

It looks like after that it starts being cautious so it definitely doesn’t go over the set value

> **🇷🇺 Оригинал**
>
> Подскажите, кто уже сушилку собирал, это нормальные тайминги нагрева для X2 версии? поставил прогрев до 90 градусов, дельта 20  
> Таймлайн:  
> 50 градусов - 2 минуты  
> 60 градусов - 4 минуты  
> 70 градусов - 6 минут, грелка 96 градусов  
> 80 градусов - 9 минут, грелка 106 градусов  
> 87 градусов - 13 минут, грелка 106 градусов  
> 89 градусов - 19 минут, грелка 102 градуса  
> 90 градусов - 24 минуты, грелка 101 градус
> 
> Он видимо дальше начинает осторожничать, чтобы точно не превысить выставленное значение

---

<div class="post-metadata">

**Author:** ![ruslan\_p\_261](https://forum.idryer.org/letter_avatar_proxy/v4/letter/r/f04885/32.png) [@ruslan\_p\_261](https://forum.idryer.org/u/ruslan_p_261)\
**Post date:** [February 23, 2026, 8:38pm UTC](https://forum.idryer.org/t/are-the-idryer-x2-heating-times-to-90-c-normal/1690/2 "2026-02-23T20:38:41Z")

</div>

That’s normal. Here’s the X4, well, X4 with spools [https://youtube.com/shorts/rkX5RD97FBM?feature=shared](https://youtube.com/shorts/rkX5RD97FBM?feature=shared)

If it feels slow, raise the delta and check the exhaust temperature 5-7 cm above the heater

> **🇷🇺 Оригинал**
>
> Это нормально. Х4 вот х4 с катушками [https://youtube.com/shorts/rkX5RD97FBM?feature=shared](https://youtube.com/shorts/rkX5RD97FBM?feature=shared)
> 
> Если кажется что медленно, подними дельту и проверь температуру выхлопа в 5-7см над грелкой

---

<div class="post-metadata">

**Author:** ![evgenii\_komissa\_8bc4](https://forum.idryer.org/letter_avatar_proxy/v4/letter/e/aeb1de/32.png) [@evgenii\_komissa\_8bc4](https://forum.idryer.org/u/evgenii_komissa_8bc4)\
**Post date:** [February 23, 2026, 8:44pm UTC](https://forum.idryer.org/t/are-the-idryer-x2-heating-times-to-90-c-normal/1690/3 "2026-02-23T20:44:16Z")

</div>

Nah, it’s fine for me. Just wanted to understand the average, so to speak) I also tried your part with a 7 mm offset and taped up the airflow channel so it would be smooth

> **🇷🇺 Оригинал**
>
> не, мне норм. хотел понять среднее по больнице) я тут ставил вашу деталь с отступом на 7мм и канал продува проклеил скотчем, чтобы гладкий был